Flux Pure Analyzer Essential v1.8.6 UNLOCKED-C0SM1CSQU1D

Soft / VST Instruments 9-04-2016
Flux Pure Analyzer Essential v1.8.6 UNLOCKED-C0SM1CSQU1D
Pure Analyzer System – The Next Generation RTA (Real Time Analyzer) System 

The Flux:: Pure Analyzer System is a network-driven modular RTA-system providing an extensive range of analyzer options for any imaginable audio analysis and measurement applications

For maximum flexibility and efficiency, Pure Analyzer presents the option to separate the signal acquisition from the analysis utilizing a Sample grabber plug-in, and in addition to the Sample grabber plug-in, Pure Analyzer also provide I/O support for ASIO and Core Audio.

Sample Grabber
Sample grabber is a standard DAW plug-in available in all common formats (VST, AU, RTAS and TDM) that acquires the source and response signals and sends the signal through the network using the ZeroConf/Apple Bonjour protocol.

You can insert as many instances of Sample grabber plug-ins as required, on the same DAW, different DAWs, and even different computers altogether, and the Sample grabber also support surround configurations. The network configuration setup for the Pure Analyzer System is entirely automatic and transparent to the user.

The audio transport requires approximately 1.4Mbps for each channel at a sample rate of 44.1kHz, so a properly configured standard Ethernet 100Mbps network should be more than sufficient to handle most cases. A 5.1 configuration at 96kHz demands a little less than 20Mbps. Naturally these requirements do not apply when using both Sample grabber and analyzer on the same hardware.

Pure Analyzer Essential
The foundation of the Pure Analyzer System is a standalone application, Pure Analyzer Essential, which can be extended with modules for Live, Metering/Loudness and Surround analysis, performing the graphic analysis rendering using a GPU-efficient 2D/3D graphic engine. The engine is based on the OpenGL standard optimizing the audio-to-visual experience utilizing the GPU on the built in graphics card.

The Pure Analyzer Essential application receives the sample feeds from the Sample grabber and analyzes them in real time. The Pure Analyzer provides the option to receive data from several different Sample grabber plug-ins on the network, and analyze the received data in parallel by selecting the actual corresponding Sample grabber to be the current source for the analysis with a simple button click. In addition to this, the input streams from the physical ASIO/Core Audio I/O can also be selected as the current source for the analysis in the same simplistic fashion.

Add-on Modules
As a complement to the Pure Analyzer Essential, three different add-on modules, all providing specific tools for their actual field of usage, are currently available. In order to use any of the add-on modules, the Pure Analyzer Essential is required.

Available add-on modules are:
Pure Analyzer Metering
Pure Analyzer Live
Pure Analyzer Multichannel
Again it's a workaround ,
porting Pure Analyzer ked v1.8.6 - (R2R realese) to Mac Users :-)
Wineskin is used and jack-ASIO (win) was pre-installed.
Wine is set to recieve audio from Loopback but it can be replaced by jack-osx or soundflower
I use loopback cause i've nothing to set ... it works.
So set Loopback (Jack-osx or Soundflower) in your DAW's output.

home page:

http://www.fluxhome.com/products/analyzer_modules/pas_spectrum
Related articles
Flux Pure Analyzer Essential v1.8.6 UNLOCKED-R2R Flux Pure Analyzer Essential v1.8.6 UNLOCKED-R2R
Soft / VST Instruments 28-03-2016
Pure Analyzer System – The Next Generation RTA (Real Time Analyzer) System 

The Flux:: Pure Analyzer System is a network-driven modular RTA-system providing an extensive range of analyzer options for any imaginable audio analysis and measurement applications 

For maximum flexibility and efficiency, Pure Analyzer presents the option to separate the signal acquisition from the analysis utilizing a Sample grabber plug-in, and in addition to the Sample grabber plug-in, Pure Analyzer also provide I/O support for ASIO and Core Audio.

Sample Grabber
Sample grabber is a standard DAW plug-in available in all common formats (VST, AU, RTAS and TDM) that acquires the source and response signals and sends the signal through the network using the ZeroConf/Apple Bonjour protocol.

You can insert as many instances of Sample grabber plug-ins as required, on the same DAW, different DAWs, and even different computers altogether, and the Sample grabber also support surround configurations. The network configuration setup for the Pure Analyzer System is entirely automatic and transparent to the user.

The audio transport requires approximately 1.4Mbps for each channel at a sample rate of 44.1kHz, so a properly configured standard Ethernet 100Mbps network should be more than sufficient to handle most cases. A 5.1 configuration at 96kHz demands a little less than 20Mbps. Naturally these requirements do not apply when using both Sample grabber and analyzer on the same hardware.

Pure Analyzer Essential
The foundation of the Pure Analyzer System is a standalone application, Pure Analyzer Essential, which can be extended with modules for Live, Metering/Loudness and Surround analysis, performing the graphic analysis rendering using a GPU-efficient 2D/3D graphic engine. The engine is based on the OpenGL standard optimizing the audio-to-visual experience utilizing the GPU on the built in graphics card.

The Pure Analyzer Essential application receives the sample feeds from the Sample grabber and analyzes them in real time. The Pure Analyzer provides the option to receive data from several different Sample grabber plug-ins on the network, and analyze the received data in parallel by selecting the actual corresponding Sample grabber to be the current source for the analysis with a simple button click. In addition to this, the input streams from the physical ASIO/Core Audio I/O can also be selected as the current source for the analysis in the same simplistic fashion.

Add-on Modules
As a complement to the Pure Analyzer Essential, three different add-on modules, all providing specific tools for their actual field of usage, are currently available. In order to use any of the add-on modules, the Pure Analyzer Essential is required.

Available add-on modules are:
Pure Analyzer Metering
Pure Analyzer Live
Pure Analyzer Multichannel
Blue Cat Audio FreqAnalyst Multi v2.2 AU MacOSX-Kleen Blue Cat Audio FreqAnalyst Multi v2.2 AU MacOSX-Kleen
Soft / VST Instruments 16-03-2016
Blue Cat's FreqAnalyst Multi is a unique multiple tracks real time spectrum analyzer: it lets you visualize the spectral content of several audio tracks on the same screen with extreme smoothness and high resolution, for both time and frequency. It is the ideal solution for mixing: you can use it as a frequency overlap detector and actually see which part of the spectrum every single instrument uses. It is now also possible to easily compare the spectrum of several instances (for EQ matching or response curve measurement) thanks to the new 'Diff' view which displays the difference between several curves.

Main Features:
Mono, stereo or mid/side multiple tracks real time spectrum analyzer: visualize and compare the spectrum of several audio tracks on the same screen.
Unique data sharing technology with multi-core processors support.
Compute and display the difference between spectra for easy EQ matching and response curve measurement.
Total control over the analysis parameters, with slope and offset correction.
Smart interpolation algorithm for extreme display smoothness.
Spectrum view with zooming and precise measurement capabilities as well as note info display.
Multiple display sizes
Instant, peak and average curves display for each track.
Choose a name for each curve for easier sharing.
Save the curves for easy A/B comparison.
Opacity control for the user interface.
Custom absolute and relative threshold control.
 
V2.2 (2016/03/03)
• VST3 plug-in format support.


TBProAudio gEQ12 v1.3.4 AAX RTAS VST3 VST CE-V.R TBProAudio gEQ12 v1.3.4 AAX RTAS VST3 VST CE-V.R
Soft / VST Instruments 14-03-2016
gEQ12 is 12 band stereo/MS graphic equalizer with accurate spectrum analyzer and minimum/linear phase modes.

Today's mixing and mastering processes require a full featured but easy to use equalizer which can accurately shape the tone of a track , bus or master track. eEQ12 provides all necessary tools in one package paired with some unique features.

The display shows the spectrum curve of incoming and outgoing signal. gEQ12 has the unique feature that the outgoing spectrum is directly calculated from incoming spectrum (incoming spectrum - filter curve = outgoing spectrum). This allows you to capture the incoming signal, to freeze it and to modify then the filter curve based on the altered outgoing spectrum. The filter response is controlled by 12 individual filter bands. Each filter band has its own display handle, which can be adjusted by mouse.

gEQ12 consists of 12 stereo filter in series. Each filter can be configured individually by setting type, stereo placement (all, left/mid and right/side), slope, frequency, gain and q-factor.

gEQ12 offers 9 analog modeled and 8 digital (Butterworth) filter. The filter quality can be increased by using oversampling. This ensures "analog" filter magnitude/phase response near Nyquist frequency. On top of it gEQ12 can operate in several minimum or linear phase modes, which can lower CPU usage and makes filter phase response linear.

12 independent filter bands, extended frequency range 10Hz - 48kHz
17 filter types, analog/digital design, zero delay IIR
filter slope up to 96dB
independent stereo/left/right/mid/side processing per band
7 processing modes: zero latency, minimum/linear phase
stereo/MS processing (e.g. stereo/mono split)
sample rates up to 192 kHz
"real" over sampling, up to 4x
hi-res spectrum analyzer with 32k FFT based ISO R40 frequencies
pre/post-EQ, average/live spectrum, stereo/left/right/mid/side
narrow-band sweeping mode
spectrum freeze mode
very easy alignment of filter response curve to audio spectrum
sample exact A/B toggle for all processing modes
precise parameter input
large and easy to use GUI
interactive spectrum/EQ display
full DAW automation support, smooth filter frequency change
64-bit internal processing
very efficient CPU usage design

1.3.4
- Small fixes
- Demo scheme changed
Blue Cat FreqAnalyst Multi 2 v2.0 MacOSX Blue Cat FreqAnalyst Multi 2 v2.0 MacOSX
Soft / VST Instruments 13-03-2016
Blue Cat's FreqAnalyst Multi is a unique multiple tracks real time spectrum analyzer: it lets you visualize the spectral content of several audio tracks on the same screen with extreme smoothness and high resolution, for both time and frequency. It is the ideal solution for mixing: you can use it as a frequency overlap detector and actually see which part of the spectrum every single instrument uses. It is now also possible to easily compare the spectrum of several instances (for EQ matching or response curve measurement) thanks to the new 'Diff' view which displays the difference between several curves.

Just like with Blue Cat's FreqAnalyst Pro plug-in, the frequency analysis can be fine tuned in details, and three modes are offered for each channel: instant, peak or average response of several audio tracks can be displayed on the same graph (the plugin supports up to 16 curves). Zooming capabilities and coordinates display let you exactly measure the characteristics of the spectrum for each audio track. Thanks to the advanced routing capabilities you can define different settings for each track and thus adapt the analysis for each audio signal you want to analyze. Our multiple tracks tutorial shows you how simple multiple tracks spectrum analysis can be.

The four memory slots let you store any curve in memory: it helps you make comparisons between several setups or portions of your audio project very easily.

Main Features:

Mono, stereo or mid/side multiple tracks real time spectrum analyzer: visualize and compare the spectrum of several audio tracks on the same screen.
Unique data sharing technology with multi-core processors support.
Compute and display the difference between spectra for easy EQ matching and response curve measurement.
Total control over the analysis parameters, with slope and offset correction.
Smart interpolation algorithm for extreme display smoothness.
Spectrum view with zooming and precise measurement capabilities as well as note info display.
Multiple display sizes
Instant, peak and average curves display for each track.
Choose a name for each curve for easier sharing.
Save the curves for easy A/B comparison.
Opacity control for the user interface.
Custom absolute and relative threshold control.
Faber Acoustical SignalScope Pro v3.8 MacOSX-PiTcHsHiFTeR Faber Acoustical SignalScope Pro v3.8 MacOSX-PiTcHsHiFTeR
Soft / VST Instruments 8-01-2016
SignalScope Pro 3 builds on SignalScope's tradition of award-winning design and precision measurement capabilities by building on advanced technology developed for Faber Acoustical's flagship product, Electroacoustics Toolbox.

SignalScope Pro is a modularized, multi-channel dynamic signal analyzer and data acquisition platform for Mac. It brings powerful tools to the Macintosh platform for multi-channel, audio-band data acquisition and real-time analysis of electrical, acoustical, and electroacoustic signals and systems. It enables precise measurements of acoustic quantities, such as equivalent and time-weighted sound levels, as well as acoustic and electroacoustic systems. The software is designed to work with any Mac-compatible audio hardware and supports multiple channels of 8, 16, 24, or 32-bit data with sample rates as high as the hardware will support.

SignalScope Pro Features
• Hardware-accelerated OpenGL graphics for fast real-time plotting
• Quartz-based graphics for high-resolution still images and prints
• Advanced control over input and output devices
• Whole device and individual channel sensitivity (level) calibration
• Support for units, including Volts, Amps, pascals, and Engineering Units
• Saving complete configurations and data in project files
• Exporting data to ascii text or MAT-files for easy import into other applications
• AppleScript support for measurement automation and remote control

SignalScope Pro 3.8
• SignalScope Pro directly supports the miniDSP UMIK-1 and Dayton UMM-6 USB measurement microphones. Sensitivity calibration data for these mics can be downloaded automatically, just by entering the mic’s serial number. Making calibrated sound level measurements is as easy as plugging in the UMIK-1 or UMM-6, typing in its serial number, and getting started with the analysis tool of your choice (the serial number only needs to be entered once, after which the app will remember the microphone sensitivity). An internet connection is required to download sensitivity information for the microphone.
• SignalScope Pro directly supports the Digiducer 333D01 USB digital accelerometer, and can automatically load serial number and sensitivity calibration information directly from the device. Making calibrated acceleration measurements is as easy as plugging in the 333D01 and getting started with the analysis tool of your choice.
• Minor bug fixes and cosmetic improvements.

Install:
Run terminal copy paste enter
sudo codesign -fs - /Applications/SignalScope\ Pro.app/Contents/MacOS/SignalScope\ Pro


Blue Cat Audio Blue Cats FreqAnalyst Multi v2.1-R2R Blue Cat Audio Blue Cats FreqAnalyst Multi v2.1-R2R
Blue Cat's FreqAnalyst Multi is a unique multiple tracks real time spectrum analyzer: it lets you visualize the spectral content of several audio tracks on the same screen with extreme smoothness and high resolution, for both time and frequency. It is the ideal solution for mixing: you can use it as a frequency overlap detector and actually see which part of the spectrum every single instrument uses. It is now also possible to easily compare the spectrum of several instances (for EQ matching or response curve measurement) thanks to the new 'Diff' view which displays the difference between several curves.

ust like with Blue Cat's FreqAnalyst Pro plug-in, the frequency analysis can be fine tuned in details, and three modes are offered for each channel: instant, peak or average response of several audio tracks can be displayed on the same graph (the plugin supports up to 16 curves). Zooming capabilities and coordinates display let you exactly measure the characteristics of the spectrum for each audio track. Thanks to the advanced routing capabilities you can define different settings for each track and thus adapt the analysis for each audio signal you want to analyze. Our multiple tracks tutorial shows you how simple multiple tracks spectrum analysis can be.

The four memory slots let you store any curve in memory: it helps you make comparisons between several setups or portions of your audio project very easily.

Main Features:

Mono, stereo or mid/side multiple tracks real time spectrum analyzer: visualize and compare the spectrum of several audio tracks on the same screen.
Unique data sharing technology with multi-core processors support.
Compute and display the difference between spectra for easy EQ matching and response curve measurement.
Total control over the analysis parameters, with slope and offset correction.
Smart interpolation algorithm for extreme display smoothness.
Spectrum view with zooming and precise measurement capabilities as well as note info display.
Multiple display sizes
Instant, peak and average curves display for each track.
Choose a name for each curve for easier sharing.
Save the curves for easy A/B comparison.
Opacity control for the user interface.
Custom absolute and relative threshold control.